• Domain Change - We have moved to https://paste-and-cut.com as our new domain.

    If you are using shortcuts or bookmarks for the old paste-and-cut.com.au domain, you need to update these or they will cease working from the 25th January, 2025. Please check the notice post for more details on this change to the forum.

Barbicide vs Isocol

babybadger

babybadger

Member
Over in the states the Yanks seem to be a big fan of 'scrubbing bubbles' and 'barbicide'. I've read around a bit (including searching through P+C's threads), and have seen that 70% alcohol is also used by those with no access to barbicide. Would you guys know of any reason people seem to prefer barbicide over alcohol?
~badger
 
Barbicide is a cationic (+ve charge) surfactant, read detergent as well as a biocide. So it would provide a cleaning effect as well as sanitising.

70% alcohol is a standard disinfectant, and works by lising the cells of bacterial.

Both should work fine.
 
I've been using Barbicide for a while and am happy with it (though am unable to test for efficacy apart from no deaths resulting from infections - oh, and no apparent infections either).
My understanding from reading various forums is that the alcohol only kills when the alcohol is evaporating, not from the actual contact so maybe not as effective on hidden gunge as soaking contact with barbicide. Alcohol is probably more likely to cause damage to some finishes as well. I don't apply alcohol to celluloid scales on straights for example.
Because I use straights the issue with the scales was the more pertinent point for me (I don't soak the scales in barbicide, just more precautionary in case of contact).
I've used Barbicide on brushes as well without any apparent ill effects or staining.
 
glenos said:
Barbicide is a cationic (+ve charge) surfactant, read detergent as well as a biocide. So it would provide a cleaning effect as well as sanitising.

70% alcohol is a standard disinfectant, and works by lising the cells of bacterial.

Both should work fine.
Click to expand...

As said, both will work very well (y) though Isocol is the cheapest and readily available including the local supermarket.
Another very cheap alternative is methylated spirits (98% ethanol) which is also readily available and is what I use.
Though not used like Isocol in businesses/practice as highly flammable hence the market for Barbicide.

If considering Barbicide and you have a mate working in a medical environment ask them about Glutaraldehyde. Similar price to Barbicide and easily more efficient. 2% Glutaraldehyde will disinfect any item completely.

Again nothing wrong with the above and all work perfectly and probably all you need. Just another modern option that is very effective to consider.

*Edit alcohol or Isocol shouldn't damage celluloid items. Acetone definitely will.
 
Last edited:
RustyBlade said:
As said, both will work very well (y) though Isocol is the cheapest and readily available including the local supermarket.
Another very cheap alternative is methylated spirits (98% ethanol) which is also readily available and is what I use.
Though not used like Isocol in businesses/practice as highly flammable hence the market for Barbicide.

If considering Barbicide and you have a mate working in a medical environment ask them about Glutaraldehyde. Similar price to Barbicide and easily more efficient. 2% Glutaraldehyde will disinfect any item completely.

Again nothing wrong with the above and all work perfectly and probably all you need. Just another modern option that is very effective to consider.

*Edit alcohol or Isocol shouldn't damage celluloid items. Acetone definitely will.
Click to expand...
Didn't know alcohol wouldn't damage celluloid. Might try it on some old scales I replaced if I've still got them there.(y)
 
Pbgoose said:
Didn't know alcohol wouldn't damage celluloid. Might try it on some old scales I replaced if I've still got them there.(y)
Click to expand...

Correction, it does and can. But it depends on the strength of it I think above ~80% and more so on a nitrate based celluloid.
If will revive the outer layer mildly. So any crystallisation or opaque layer will be removed or cleared. Nitrate based will regel the celluloid if I'm remember rightly with pure enthanol but leaves a residue of byproduct that buffs off.
Low solutions are fine for cleaning but don't soak it.
We restored a celluloid camera Case with abrasives and alcohol to clean it.
You would have to use alot or soak it to wreck it.

*Edit Hold off. Did some more reading on this. Going to email a chem mate to confirm this further.
 
Last edited:
RustyBlade said:
Another very cheap alternative is methylated spirits (98% ethanol)
Click to expand...
The water in the 70% ethanol mix is important, pure is not as effective, unless you ignite it. The water allows penetration into the cell to denature the proteins on the inside. So, 180ml of your finest method diluted to 250ml with tap water will get the job done.

The quaternary ammonium chloride in barbicide is pretty reactive, and will tear cells apart.

An aqis approved cleaning agent is Virkon.
Virkon disinfectant (active ingredient Potassium peroxymonosulphate)
Applied as per manufacturer’s instructions on animal, plant and microbial goods.
Sold as 1% Virkon S (Antec International) or 1% Viricidal X (Johnson Diversy)
Click to expand...

My organic chemistry is horrible so I cannot comment on the celluloid scales questions.
 
Used alcohol for str8s for a very short while but have been using barbicide for years now, tried and true is the theory
Ii use it for others str8s before use then post shave testing before sending out after honing ,
It is relatively cheap realy, as it is diluted about 10:1 with water for use and each batch lasts a long time if kept out of sunlight also,
10 minute max soak and you are good to go
I never submurge the scales in it as it will stain some light materials, but it is only the steel that needs doing anyway
And most vintage Str8's or DE's for that matter that have sitting for years will be safe anyway as nearly all bugs die after a couple of years I am lead to believe, plus any polishing or honing will remove them as well
 
What @Substance has written is my experience. I use a double-strength version of the barbicide... only because the hairdressing supplies place near my work, had run out of actual barbicide.

The only issue I have read about that alcohol doesn't affect, is spore-based cling-ons. Some of the big words that @glenos has mentioned, are very effective at neutralising these. Apparently, so is a 3% solution of hydrogen peroxide.

A lot of vintage instruments from out in grazing country, apparently are prone to having small amounts of historical anthrax spores on them, which are capable of laying dormant for more than 70 years. That factor doesn't bother me too much, but I like to know a clean blade is scraping my face.
 
AussieTanker said:
Is there an Aussie equivelent to "scrubbing bubbles" .... and where would you buy barbicide from here in Aussie?
Click to expand...

Scrubbing Bubbles is just a US range of household cleaners. You can check out the ingredients of each here. Spray & Wipe is probably the Australia equivalent but I tend to use this one to clean razors.

Barbicide is available on eBay here in Australia, see here for example, and possibly from local barbers suppliers.
 
You must log in or register to reply here.
Back
Top